Closed Thread
Results 1 to 7 of 7

Thread: danospool - chalking paint

Hybrid View

  1. #1
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,384

    Default Re: danospool - chalking paint

    No, your info is relevant.

    Based on what you just told me, the chalking is probably a result of the paint you applied. If it's chalking only a little -- enough to mark the bottom of your feet the FIRST time you walk on a particular area but not enough to cloud the pool, you might have used Zeron. In that case, there's nothing to fix: that's just how epoxy is.

    If it's chalking more than that, you can RECOAT epoxy with better epoxy, if you prep the surface properly. That would allow you to go to a Zeron finish, which would still chalk as above.

    Ben

  2. #2
    Join Date
    May 2011
    Location
    Western Washington
    Posts
    9

    Default Re: danospool - chalking paint

    Just thought I'd give an update on the paint situation. Looks like the mono-epoxy stuff we used is crap. As soon as we started using the pool this summer, the paint started coming loose in some areas of the pool, especially the benches and steps, and peeling off in big pieces. I can see blisters and cracks in the deeper parts of the pool also. Just so everyone knows, the paint we used was LifeGuard Mono-Epoxy over their etching primer. Both are sold by Top Secret Coatings, which sells many types of paint over the internet. Some people claim to have had success with their pool paint, but I'm not one of them. The vendor says the paint failed because of moisture corruption before the paint was fully cured. I say hogwash, but that's between me and them. Just be forewarned that this paint is apparently very, very difficult to apply properly. I followed all the instructions faithfully, but apparently that wasn't good enough. DIYers beware!

    All that means that we will have to drain the pool again, remove the finish(sandblasting this time), and try something else. Ben, I gather that you are not a big fan of painting pools, so what do you think of replastering? If a replaster job is done right and maintained properly, will it last a good long time? I'm at the point where I'm a little gun-shy about painting again, so my wife and I are seriously thinking about replastering, even though it is quite expensive. Any thoughts or guidance you may have would be welcome.

    Dan
    Inground gunnite/plaster/fiberglass, 30,000 gal.
    Sand filter-PacFab Superflow (using crushed glass), 1 HP Hayward Super Pump
    Natural gas heater-RayPak

Closed Thread

Similar Threads

  1. Pool Paint?
    By jrittger in forum In-Ground Pool Construction and Repair
    Replies: 2
    Last Post: 05-02-2012, 10:27 PM
  2. Paint
    By Robie in forum In-Ground Pool Construction and Repair
    Replies: 1
    Last Post: 03-16-2012, 04:44 PM
  3. Update-chalking paint
    By danospool in forum In-Ground Pool Construction and Repair
    Replies: 5
    Last Post: 08-10-2011, 10:57 PM
  4. chalking and painted pool
    By tomdow2 in forum Dealing with Alkalinity and Calcium
    Replies: 1
    Last Post: 05-26-2007, 09:24 PM
  5. Pool Paint....
    By djhop in forum In-Ground Pool Construction and Repair
    Replies: 1
    Last Post: 07-16-2006, 10:07 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts