Low pH

[mwsmith2]

Yes, add borax to raise your pH. Not sure why your pH is low, you didn't really give much information, other than indicate you had a problem. How low is low? How big is your pool? How are you chlorinating? This will help us narrow down the cause of your low pH.

It's unlikely that a pool cover would impact your pH.

Michael

[CarlD]

Bet you use Tri-Chlor pucks to chlorinate your pool. They are VERY acid and drive pH down.

Otherwise, MW Smith is right. I ONLY use 20 Mule Team Borax (from the grocery store) to raise my pH. I usually add 1/4 box at a time, wait 12-24 hours then test and add again as needed. However, if my pH is SERIOUSLY low (<6.9), I'll dump in a whole box, wait 6 hours, then test again and add if needed. BTW, my pool is 20k and vinyl lined.

[Poconos]

I think part of the original question dealt with adding borax right in the skimmer. Yes. It will get sucked into the filter and then dissolve rapidly. Within minutes.
Al

[howbout]

Yes, I did want to know about putting it in the skimmer - I actually just went out shopping and got some Borax.

The problems we had were low to no chlorine and the dreaded black algae but we got that under control. We used to have a service, but stopped it b/c the guy wasn't showing up and was saying he did. AND on a weekend we wanted to use the pool it was GREEN. So we figured if it's going to get green it may as well be our fault

So right now I am in learning mode and VERY glad to have found this forum. I am going to add some Borax to the skimmer - the pH isn't HORRIBLY low but IS low and since I have kids who swim and their friends as well I always want the pool balanced perfectly.

You could say I've become obsessed with it I guess

Oh - forgot to say...it is an inground pool, about 15X30 but L shaped - it holds 11,620 gallons. And yes, we use the tabs to chlorinate, we were told they are the best way! Guess I have a lot to learn...what IS the best way to chlorinate if not with the tabs???

[Watermom]

In my opinion, simply by using plain, unscented household laundry bleach. It is what many of us use. I use it exclusively and always have. In fact, I have never used any pucks at all in my pool nor any other chlorine source at all. Bleach works great, is cheap, readily available. The only downside for some people is carrying the jugs. But, that is not a big deal for me. In my pool, 24ft AG, I typically keep my stabilizer (cya) reading around 30-40 and add approximately 2-3 quarts (not jugs) of bleach per evening. It is easy for me. Takes me about 3-5 minutes per day.

Watermom

[CarlD]

the pH isn't HORRIBLY low but IS low and since I have kids who swim and their friends as well I always want the pool balanced perfectly.

You could say I've become obsessed with it I guess

Oh - forgot to say...it is an inground pool, about 15X30 but L shaped - it holds 11,620 gallons. And yes, we use the tabs to chlorinate, we were told they are the best way! Guess I have a lot to learn...what IS the best way to chlorinate if not with the tabs???

The tabs are why your pH is low--they are super-acidic. Stop using them and switch to bleach and the pH should rise without doing anything else. Check your total alkalinity--it should be 90-125. If it's lower add baking soda--start with 1 lb, wait 12-24 hours, and test again. Keep going until it's in range. Since you have a vinyl pool, don't worry about it being too high unless you reach the 190-200 range--then you have to lower it, which is a pain, and explained elsewhere. But anything up to 180 in Total Alkalinity is not a problem--because you have a vinyl pool.

You also MUST get your CYA level measured--also called Cyanuric Acid, Stabilizer or Conditioner. That determines the minimum level of chlorine you need to maintain--and the max you can use to shock the water.

Since you've been using pucks, (I guessed right on that, didn't I? ) I'm also guessing your CYA is through the roof--100ppm or more. If so, you will either need to drain off a lot of water and replace it, or maintain very high chlorine levels--8-10ppm normally, and 20-25 to shock. Only practical way to lower CYA is by dilution--draining it off and replacing the water. (there is another way but it's very messy and unpleasant).

If you have CYA > 100ppm and are trying to maintain chlorine levels in the .5-3ppm range I can guaranteed you are headed for algae central. Pool guys usually mess this up and add tons of chems. Yours didn't--the clown didn't even show up! I suggest you pay him with Monopoly money--you'll stop pretending to pay him when he stops pretending he's working.

[howbout]

Since you have a vinyl pool, don't worry about it being too high unless you reach the 190-200 range--then you have to lower it, which is a pain, and explained elsewhere. But anything up to 180 in Total Alkalinity is not a problem--because you have a vinyl pool.

Pool guys usually mess this up and add tons of chems. Yours didn't--the clown didn't even show up! I suggest you pay him with Monopoly money--you'll stop pretending to pay him when he stops pretending he's working.

Thanks for the info..but we do NOT have a vinyl pool, it's an inground. about 15X30 L shaped...and we fired the guy from the service last year (though that would have been a great idea with the money)

In any case, since I have added the Borax the levels have been perfect. I check every day...

Thanks again!

[CarlD]

You are very welcome. But do yourself a favor and post your water test numbers--it's easier to see what's going on then, but at least, for now, it sounds like things are good.