+ Reply to Thread
Results 1 to 10 of 51

Thread: Low ph and algae

Hybrid View

  1. #1
    Watermom's Avatar
    Watermom is offline SuperMod Emeritus Quark Inspector Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars
    Join Date
    Dec 1969
    Location
    Charleston, WV
    Posts
    9,244

    Default Re: Low ph and algae

    Here is a link to the videos:> http://pool9.net/K2006-vid/

  2. #2
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,207

    Default Re: Low ph and algae

    CH level?

    With algae, and a CYA level of 70+, you need to maintain FC levels of 15 - 20 ppm. If you have mustard algae, even higher levels are required.

    Watch the videos, and redo any tests you overlooked or might have done incorrectly: FC, CC, pH, TA, CH & CYA.

  3. #3
    Join Date
    Jul 2014
    Location
    MI
    Posts
    48

    Default Re: Low ph and algae

    I watched the videos. Thanks that was help. I redid test.
    Cl 5.6 ppm
    Com cl 0 stayed clear
    Ph 7.3
    Alk 100
    Hardness ca. 125
    Cya 75

    I have 3 gallons of bleach here and 2 boxes borax and 1 box baking soda
    14k gal AG pool, 150 sq ft cart filter. PF=8

  4. #4
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,207

    Default Re: Low ph and algae

    Good!

    Then you just need to adjust your chlorine upward, hold it there, and brush regularly.

    Normally, your chlorine level should be 10% of your CYA level (7 ppm). When you are dealing with algae, you'll need to go to 20% (15 ppm) or higher and HOLD it there, till the algae is gone.

    Physically brushing the pool surfaces, to break up the self-protective layer of slime that algae colonies produce, is VERY important. Chlorine does NOT penetrate slime well. Some other algaecides (monochloramine, copper) penetrate much better, but at the cost of some serious side-effects.

    A gallon of 8% bleach contains the equivalent of about 0.7 lbs of chlorine gas (100% available chlorine). Your PF is 8, so each gallon will add a little less than 6 ppm of chlorine (0.7 x 8 = 5.6) to your pool.

    Most dichlor is 61% available chlorine, so a pound of dichlor would add about 5 ppm (0.61 x 8 = 4.9) of chlorine and about 4.5 ppm of CYA to your pool.

  5. #5
    Join Date
    Jul 2014
    Location
    MI
    Posts
    48

    Default Re: Low ph and algae

    How much bleach would you suggest? How long do I keep it that high? Just till it's dead or much longer? Should I stay with bleach after this or go back to my unopened tab? Sorry for the questions never had this before and don't want it again.
    14k gal AG pool, 150 sq ft cart filter. PF=8

  6. #6
    Join Date
    Jul 2014
    Location
    MI
    Posts
    48

    Default Re: Low ph and algae

    Which works quicker in killing this the 6 gallons of bleach or 5.5 tabs? Of course with me brushing and cleaning
    14k gal AG pool, 150 sq ft cart filter. PF=8

  7. #7
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,207

    Default Re: Low ph and algae

    It takes days for trichlor to dissolve, so the bleach.

  8. #8
    Join Date
    Jul 2014
    Location
    MI
    Posts
    48

    Default Re: Low ph and algae

    Do I put all 6 bleach in at on time or do 2 then check clorine?
    14k gal AG pool, 150 sq ft cart filter. PF=8

  9. #9
    Watermom's Avatar
    Watermom is offline SuperMod Emeritus Quark Inspector Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars
    Join Date
    Dec 1969
    Location
    Charleston, WV
    Posts
    9,244

    Default Re: Low ph and algae

    You cannot shock a pool with trichlor tabs.

    You want to maintain this high chlorine level until you meet 3 criteria:
    1) You can go from sundown one evening to within an hour of sunrise the next morning without losing more than 1ppm of FC.
    2) You have no higher than 0.5ppm of CC
    3) Your water is clear and there are no visible algae spots.

    Then, keep it high for one additional day for added insurance and then let it drift back down. At that point, you need to keep your chlorine level between the minimum and maximum based on your CYA level. http://pool9.net/cl-cya/

  10. #10
    Join Date
    Jul 2014
    Location
    MI
    Posts
    48

    Default Re: Low ph and algae

    Numbers as of today.
    Cl 16.4
    Ph 7.5
    Cya 75
    How do I keep my clorine at that number to kill the algae? Besides doing the usual cleaning, brushing, and vacuuming. I have 2 tabs in the floater and have been checking the chemicals daily in the moring. Is there something else I need to add? Should I add more bleach? There was 1 small spot of green in pool yesterday and the sock on skimmer basket was slight green this morning.
    14k gal AG pool, 150 sq ft cart filter. PF=8

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts