+ Reply to Thread
Results 1 to 10 of 47

Thread: Too much DE in pool

Hybrid View

  1. #1
    Pappy is offline PF Supporter Widget Weaver Pappy 0
    Join Date
    May 2014
    Location
    Plano, TX
    Posts
    261

    Default Re: Too much DE in pool

    I'm absolutely certain that MOST of the time, the experts here, and I'm not one of them, advise against flocculants. That might clear the DE out of the pool quicker, but many flocculants contain other "stuff" that is bad for your pool and often introduce other issues that are much more difficult to correct than filtering excess DE from the water. I assume you are running the pump 24/7? Are all your test kits strips? If you have a drop based (titration) kit, that will probably get you by for now.
    Intex 15ftx4ft 4500 gal. 3/4 HP Pentair WhisperFlo pump. Hayward 21" sand filter. Taylor K-2006 & K-1106 kits. PF=27

  2. #2
    Pappy is offline PF Supporter Widget Weaver Pappy 0
    Join Date
    May 2014
    Location
    Plano, TX
    Posts
    261

    Default Re: Too much DE in pool

    Also, if PoolDoc or one of the others does advise a flocculant later, maybe they can offer a good choice brands. Waiting a day at this point isn't going to make much difference, and it is much easier to add something tomorrow, than to remove something you shouldn't have added today. POP means Pool Owner Patience - that's a term that I learned here. I've often heard that lack of POP is one of the biggest problems pools have.
    Intex 15ftx4ft 4500 gal. 3/4 HP Pentair WhisperFlo pump. Hayward 21" sand filter. Taylor K-2006 & K-1106 kits. PF=27

  3. #3
    Join Date
    Jul 2011
    Location
    Los Angeles, CA
    Posts
    48

    Default Re: Too much DE in pool

    OK, thanks. The test kits are 2 drop, 1 strip.

    And no, it's not on all the time. I ran it that way for 3 or 4 days and saw no change.
    20,000 gallon plaster (concrete) pool
    DE filter
    Nature 2 (unchanged)

  4. #4
    Pappy is offline PF Supporter Widget Weaver Pappy 0
    Join Date
    May 2014
    Location
    Plano, TX
    Posts
    261

    Default Re: Too much DE in pool

    Running 24/7 will clear up the excess DE faster, and you'll have to clean it more often. Have you tested chlorine and ph levels with a drops kit? Do you know what your CYA level is? I was under the impression that DE filters "like" to be run constantly to keep the from dropping off the grids. BUT again, I'm not the DE filter expert.
    Intex 15ftx4ft 4500 gal. 3/4 HP Pentair WhisperFlo pump. Hayward 21" sand filter. Taylor K-2006 & K-1106 kits. PF=27

  5. #5
    Join Date
    Jul 2011
    Location
    Los Angeles, CA
    Posts
    48

    Default Re: Too much DE in pool

    Yes, I've tested with the drops kit, and I'm good on chlorine levels. CYA is hard to tell, but might be a bit low.

    Many thanks for your help.
    20,000 gallon plaster (concrete) pool
    DE filter
    Nature 2 (unchanged)

  6. #6
    Join Date
    Jul 2011
    Location
    Los Angeles, CA
    Posts
    48

    Default Re: Too much DE in pool

    BTW - if anyone cares, this problem has been going on for two months now, but until yesterday, and for the longest time, I was unable to get into this site.

    It takes an inordinate amount of my time, and has my wife saying, Let's just drain the pool and leave it empty.
    20,000 gallon plaster (concrete) pool
    DE filter
    Nature 2 (unchanged)

  7. #7
    Pappy is offline PF Supporter Widget Weaver Pappy 0
    Join Date
    May 2014
    Location
    Plano, TX
    Posts
    261

    Default Re: Too much DE in pool

    I don't know what to tell you about not being able to get into the site. Is the your filter pressure climbing? What is the current water condition? Are you able to post actual numbers for chlorine, ph, and cya levels? Nobody can help very much when they have no idea what they are working with. Draining a pool, even a concrete pool, can cause severe damage.
    Intex 15ftx4ft 4500 gal. 3/4 HP Pentair WhisperFlo pump. Hayward 21" sand filter. Taylor K-2006 & K-1106 kits. PF=27

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts