Ordered My Pool

[dcombs44]

Thanks!

So, we had the sod removed last week, but I kept getting rained out on days I planned to work on leveling.

Well, we finally got to start yesterday (heat index of 110 degrees). About 4 inches down on the high side was a 4' x 10' slab of 10" thick concrete. Grrrrrr....

Took a big chunk of the afternoon to bust up the concrete and remove it.

Ended up getting a few of the blocks set for the posts using a laser transit level. Had to dig down a fair amount though, so we've got a fair amount of digging and raking left to do.

Back to the grind after work today.

[Watermom]

HARD WORK!!! But, will be SO worth it. Just keep picturing you floating on a raft with a cold drink in your hand!

[dcombs44]

Well, it's been a struggle, but we're almost there.

We started filling the pool last Friday afternoon. I took the day off to finish getting the walls up and the liner in. At about 9:00 pm after 10 hours or so of working on the pool, the liner slipped and couldn't be stretched back over the side. At that time, there was about 1.5 feet of water in the pool. So, we drained, replaced the sand that had washed out, refit the liner, and started refilling on Sunday.

I'm filling with a garden hose, so it's a slow process. Got it filled to just below the return yesterday, so I got the return and skimmer installed, and got the filter completely installed.

Will finish filling tonight, test the pump and add chlorine. This is day 3.5 with no chlorine, so I'm ready to get some sanitizer in there to keep from an early algae bloom. Assuming we finish filling and add chlorine tonight, we should be swimming by tomorrow.

What a process.

[Watermom]

I'd suggest going ahead and getting some chlorine in there now instead of waiting any longer. You are pushing your luck with that long with no chlorine and hot weather. Add some bleach and then take a clean broom or something and stir it around. You don't want to chance a brand new pool with green water and it will happen way faster than you would think. Add a 3-quart jug of bleach. Walk around the perimeter of the pool and reach as far away from the side as you can and drizzle it in slowly and then stir it around.

Also, remember that a pool with no cya in it will lose chlorine fast. So, be prepared to test and add chlorine at least twice a day for the first week or so until you get a cya reading. And, if somebody is home in the afternoon, maybe even test/dose then, too.

[dcombs44]

ok. I'll switch out of the shirt and tie at lunch and add some chlorine. I bought a few jugs of bleach last night as well as some borax and dry acid.

My tap water was testing a bit high initially, so I wanted to be prepared to get it down to where it needs to be. Once the pump is running, I'll get some CYA added.

Am I right that I read to hang a sock in front of the return to add CYA?

[Watermom]

You can either do it that way or you can mix it in a bucket of water and then slowly pour it into the skimmer. (That is the way I add it in my pool.) If you put it in the skimmer, just remember not to backwash your filter for about a week to give it time to dissolve. I also run the pump 24/7 for the first couple of days after I add it.

Also, don't test for it or add any more for about a week to make sure it has time to dissolve.

[dcombs44]

Added a jug of bleach and did a quick test with the wal-mart kit after I stirred it up.

.5 ppm chlorine
7.8 pH

I'll finish filling the pool tonight and run a full battery of tests with the Taylor Kit. The plus side is that our tap water reads .5 ppm of chlorine out of the tap, so as we add water, we're adding a decent amount of chlorine (or so it seems).

Should I try to get the chlorine to shock level off the start, or should I just keep it at recommended levels until CC is over .5 ppm? I was planning on trying to get it between 1 and 3 ppm before bed tonight and checking it again in the morning.