+ Reply to Thread
Results 1 to 10 of 27

Thread: Super II Pump Replacment Decision

Hybrid View

  1. #1
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,384

    Default Re: Super II Pump Replacment Decision

    I'd replace the whole pump . . . and go to a 2-speed! Check on what rebate you can get from your power utility -- it may be substantial.

    Take a look at this page: http://www.a1poolparts.com/-strse-Pu...Categories.bok for pricing. Allow $50 or more for shipping. A1PoolParts has *seemed* reliable; I've used them myself a couple of times, and they do have a physical location and a real store, so they are not like a lot of the Internet sites that are just an office, with 10 pool guys who can order for them.

    You'll have to add either a timer or a toggle switch:
    Intermatic T10604R Pool/Spa Control Center T106M and T104M @ Amazon
    Southwire 55189301 3/4-Inch 6-Feet ULTRA Whip-Pre-Assembled with Wires and Connectors @ Amazon
    Leviton 1282 15 Amp, 120/277 Volt, Toggle Double Throw @ Amazon

    But, you should get payback -- even without a rebate -- in a year or two, and you'll get a MUCH quieter pump, as well as BETTER filtration. (All filters work better with slow flow for more hours, rather than high flow for fewer hours.)

  2. #2
    Join Date
    Oct 2011
    Location
    Orlando, FL
    Posts
    13

    Default Re: Super II Pump Replacment Decision

    Thanks. The thing w/ 2-speed is that I have a solar heating system with panels on the 2nd story roof, so I wasn't going to attempt trying to figure that out at this time. My current pump is SP3010X15AZ (or at least that's what I figure the replacement needs to be - my label is totally worn out). All I really have is the label on the motor, which is 1.5 HP, SF 1.

  3. #3
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,384

    Default Re: Super II Pump Replacment Decision

    Hm-mh.

    Need pictures and drawings, sent to [email protected].

    Does your solar system have a vacuum relief valve? If not, you can use a timer to start on high, get the air out, and then switch to low. But, you'll need to do that 2x per day, to avoid air locking the solar system.

  4. #4
    Join Date
    Oct 2011
    Location
    Orlando, FL
    Posts
    13

    Default Re: Super II Pump Replacment Decision

    Thanks for the advice, but I don't think I'm ready to do this major upgrade. I'm very conservative. Also, I wanted to be able to keep the current motor and put it back on when the new one goes. What I would maybe like to do is get the EE version of the Super II for now. But I'm confused. What I have now is SP3010X15AZ. This is 1.5 HP, 1.0 SF. The EE line has a SP3010EEAZ model, which has 1.0 HP but 1.5 SF. Their higher rated is SP3010X15AZ, which has 1.5 HP, but 1.35 SF. There is a chart here. http://www.inyopools.com/Products/02201169001153.htm. Will the 1HP, 1.5 SF be 100% equivalent to what I have now? I've tried to understand the HP/SF connection, but (seeing that I'm conservative bordering on the scared), I am just looking for confirmation that SP3010EEAZ is the exact replacement for me and that I can use my current motor back on it when the time comes. Does this make any sense?

  5. #5
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,384

    Default Re: Super II Pump Replacment Decision

    Here's the crossover data from Hayward:

    ( http://www.hayward-pool.com/prd/In-G...1_14002__I.htm )

  6. #6
    Join Date
    Oct 2011
    Location
    Orlando, FL
    Posts
    13

    Default Re: Super II Pump Replacment Decision

    OK, thanks again. So it looks like they are interchangeable, yes??? I even called Hayward, they said so, too. BUT: they also said the amp draw on BOTH is IDENTICAL on SP3010X15AZ and SP3010EEAZ. How can one be more energy efficient if they draw the same amps? On the Inyo chart, this looks different, with a lower amp on the EE pump. To make me even more confused, the manual has a KW number that is 1.1 for the regular and .75 for the EE. And it states to make sure one has the correct wire for the KW number. So is this a problem when installing? I actually ordered the EE already, but now I'm STILL not sure if it was the right move? Thanks....

  7. #7
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,384

    Default Re: Super II Pump Replacment Decision

    Quote Originally Posted by versstef1 View Post
    I actually ordered the EE already, but now I'm STILL not sure if it was the right move?
    The time to decide whether you're going to jump in, is before you're in the air. Once you're in the air, it's better to concentrate on not going SPLAT!

    What you've run into is the old 'up rate' vs 'full rate' label game pool pump manufacturers have been playing for years. The *ONLY* difference between an SP3010EECZ and a SP3010X15AX is the label -- there is NO other difference: same parts; same motor (except the label); same efficiency; same wiring.

    Stefan, you have ALREADY made your choice. I don't see a lot of value in discussing whether it was the best possible choice, especially when we are so far behind in trying to help people. If you change your mind, and send it back, let us know, and we can look at it again.

    Maybe.

    You already know it's not what I would recommend.

    We absolutely believe in everyone's right to make their very own choices about their pool gear. If they want to buy SuperDuper All Eco Friendly DayGlo Pool Slime for $200 per ounce . . . we think that's absolutely their right (so long as it doesn't poison the neighbors ). But, we don't see a lot of point in discussing it with them -- it's not a product or an approach we support. We're not mad; we just need to focus on helping people who ARE listening to our advice.

    Best wishes!

+ Reply to Thread

Similar Threads

  1. Hayward Super Pump is Super Noisy
    By moneypitpool in forum In-Ground Pool Construction and Repair
    Replies: 6
    Last Post: 07-25-2011, 10:16 AM
  2. Hayward Super Pump - Super Hot and Shutting Off
    By CapitalBoo in forum Pool Equipment & Operations
    Replies: 0
    Last Post: 06-18-2011, 09:32 AM
  3. Hayward Super Pump Really Hot...HELP?
    By calamtykel in forum Pool Equipment & Operations
    Replies: 6
    Last Post: 06-14-2009, 04:30 PM
  4. Pump seal for Hayward super pump?
    By goosegunner in forum Pool Equipment & Operations
    Replies: 1
    Last Post: 05-22-2006, 01:34 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts