Newbie with pool chemistry issues

[Watermom]

it would be best for us to verify what his actual CYA reading is before advising him to drain.

[pool2012]

I retested with the dilution method and FC looks like 2 to 2.5, CC is the same.
Since July 1st, when we noticed our eyes burning and realized our pH was about zero (but the pool looked crystal clear), we've added approx 18 pounds of baking soda. With no improvement in pH we raced to the pool store, which prescribed more baking soda(14 lbs) and soda ash(1.25 lbs). With this addition the pH was readable, but the TC was off the chart high and the FC was low and the pool was cloudy. Realized we needed another solution to the problem since the pool store wanted to address hardness and we have a fiberglass pool...and hardness level was good. Saw this website and found that we might be low on chlorine since our stabilizer was so high (from our intense use of pucks, usually 4 at a time in a floater). The pucks are out. We added 6 qts of bleach before I decided we better verify before we get to far gone.

[pool2012]

I just tested this morning with these results: TC 10 CC 10 (both with dilution method), pH 7.6 TA 220 Stabilizer (with the test strip) maxed at 150.
The pool water appears more cloudy than yesterday, but the yellow tint is gone. I've brushed the sides three times yesterday and will vacumn now. It appears the TA has increased overnight. Yesterday I had 210 and today I have 220. Perhaps that is change of 10 is not significant? Since the water is still cloudy I need to increase chlorine until it clears? Thanks!

[Watermom]

I'm skeptical of that CC reading of 10.

Try your CYA test using the disappearing black dot test instead of strips. You'll have to dilute the sample to get a reading. Take one part pool water and one part distilled water. Mix and then run the test on that. Multiply your result by 2. If you still show a reading of 100 with that, do it again but this time take one part pool water and two parts distilled. Multiply the result by 3. This dilution method won't be super accurate, but will at least get us a better ballpark reading of what your CYA actually is. At any rate -- no more trichlor pucks or dichlor shock powder in your pool!

What is your calcium hardness reading, by the way?

You are right that a 10ppm difference in your TA results is insignificant. But, your alk is to high. Please read the following two guides:

Lowering Alkalinity Step-by-Step

Using Muriatic Acid Safely

Yes, you will have to keep your chlorine high. Please read the Best Guess Chlorine Chart in my signature below. Also, with such a high CYA pool, you are going to have to have the K-2006 kit. The other kits are not going to be able to read the high chlorine levels you are going to have to run. Test kit page in my signature above.

[pool2012]

TH was 100 at 7:15 this morning.
The FC and the CC were the same color on my test this a.m. I used a 1 pool : 4 distilled water dilution that showed 2.5: which would give me 10.
I don't have a disappearing black dot test. All I have is the 5 test kit and strips...I know I need the more extensive kit but I can't locate it locally and it takes time for delivery.
The pool is now cloudy to the point I can barely make out the vacumn head at the bottom of the 5 foot deep end.
When you advised to keep the chlorine high, I follow the chart according to my stabilizer level of 150...so I should maintain 25ppm and test the level with the dilution method. And I believe I read 2.5 gallons of bleach raises chlorine 5ppm per 10k gal...so in theory (assuming the FC is 10) I would add 7.5 gallons of bleach.
Then I'd add acid to lower the TA. Sound right?

[Watermom]

1 gallon of 6% bleach will add 6ppm of chlorine. Do NOT add 7.5 gallons to your pool!

Did you order the K-2006 kit yet? It is not sold locally.